Latest Trending Tech & Gadgets Lifestyle Apple Android

Hot Hobbies & Toys Posts

iOS 18 Tips, Tricks, How-Tos, News

How To: Control tail spin on a PicooZ mini helicopter

To begin in controlling the tail spin on your helicopter you need to turn your helicopter on and then turn the controller on. On your controller there are two trim bars. If it begins spinning to the left, tap the right trim; likewise, if it begins spinning too much to the right, tap the left trim. Unfortunately there is no memory in the PicooZ helicopter, so every time you turn on the helicopter you have to trim it. In the example video the helicopter needed to have the trim bar pressed 12 ti...

How To: Power a toy car with a balloon

Karthik Raj and Nishant explained about a air balloon car in this video. You just need 4 or more things to make the air balloon car. You need two rubber bands, one pen, two toy cars, and one air balloon exactly to do this air balloon car. First of all, you just take the air balloon and fix it one side of the pen which is opened two sides. Next place the pen on the top of the toy car and tie with a rubber band and make sure that the rubber band is in the middle of the toy care and not in the t...

How To: Make a boomerang out of styrofoam cups

Crazy Chris shows us how to make a cool boomerang out of two Styrofoam cups - useful as a party trick. Plastic and paper cups can also be used. The bottoms of the cups are taped together. The key to making the boomerang work is the positioning of the fingers on the cups. The middle finger should be placed in the middle joint of the two cups - the fingernail in contact with the tape. The pointer and ring fingers should support the top of the cups and the thumb gives the bottom support. Chris t...

News: PAARRRTY! Robo-Drummers and Pole Dancing Stripper Bots

Artist Giles Walker's robot peep show/DJ installation piece gives us a little glimpse of what strip clubs could look like in the future (well, let's really hope not, guys). Walker also teams up with Frank Barnes and his robot drummers (second video in the gallery below, check it out - pretty sweet). Previously, Sexxxy Roxxy: World's First Sex Bot (NSFW).

How To: Clean dirty coins using multiple methods

Kevin demonstrates multiple methods to clean dirty coins.In the first method he takes some coke in a glass and hangs a dirty coin in it with the help of a string. This coke technique takes a few hours.In another faster technique which takes only 20 to 30 minutes he takes table salt and food vinegar. He takes the table salt and dissolves it in vinegar in a bowl. When most of it is dissolved he drops a dirty coin in it and waits about 20 minutes.Another method is to rub toothpaste on the coin f...

How To: Clean pennies with taco sauce

In this video, we learn how to clean pennies with taco sauce. To do this project, all you need are some dirty pennies and a paper plate! First, pick out some really dirty pennies and grab a taco sauce packet you have laying around the house. Grab a paper plate and pour the taco sauce onto the top of your pennies. The taco sauce has vinegar in it, so it can clean the pennies easily. Let it set for a few minutes and then rinse the pennies off in water. This will clean your dirty change and is a...

How To: Set rotor blade pitch and speed on a Honey Bee King 3

Alishanmao demonstrates on a Honey Bee King 3, how to change the pitch and speed. Using the radio knob in the controller you can change the pitch of the main rotor. Make sure your 3D switch is off, that your throttle is at zero, and after connecting the battery, do not move the battery until you here it beep to confirm it is ready. When pitch is at its minimum you will have less rotation speed and at its maximum you will have a higher rotation speed. The best thing to do is to try and find a ...

How To: Perform the wrist mount to green triangle yo-yo trick

In this video tutorial, viewers learn how to perform the wrist mount to green triangle yo-yo trick. Begin by throwing a wrist mount with the yo-yo. Put your non-throwing hand's index finger into the string that is furthest to your right. Now do an underpass to the right. Let off the string with your throwing hand and you should now have formed a green triangle. To dismount, simply pop the yo-yo out from the back and land on a trapeze. This video will benefit those viewers who enjoy playing wi...

How To: Make homemade 3D glasses

In this tutorial, we learn how to make 3D glasses at home. First, take cardboard and cut two square holes in it. Then, take clear packing take and tape it over the holes. Once you've done this color the front of the tape with a red marker on one of the sides. On the other side, take a blue marker and color it in. That's all you need to do to watch 3D movies and television shows in the comfort of your own home. These are extremely inexpensive and can be made within just a couple of minutes. It...

How To: Build a LEGO desk

This video is about making a LEGO desk, which is used for placing computers. The video shows the first step by taking few pieces of wood and making into pieces. Then two of the pieces are placed one over the other and placed in the left side and the other single piece is placed on the right side. Another piece is placed on the top of the pieces placed in left and right positions. After everything is placed it gives the perfect shape of a computer desk and a toy computer is also placed on the ...

How To: Make a lego lightsaber

In this how-to video, you will learn how to design and create four of your own Lego light sabers. All you need is six different pieces as seen in the video for the first design. Now connect them vertically, one at a time. All you need is six different pieces as seen in the video for the second design. Now connect them vertically, one at a time. All you need is seven different pieces as seen in the video for the third design. Now connect them vertically, one at a time. For the last design, you...

How To: Deal with a flooded Nitro engine on an RC vehicle

Alishan Mao describes how to fix a flooded Nitro Engine on an RC car, remove the excess fuel, and start the engine. Flooding of the engine can occur when priming the engine. If you prime the engine too much, the engine can get flooded, making it difficult to pull the pull start. A simple way to fix this is to remove the glow plug. Cover the top of the engine with cloth or rag and hold it there so that the fuel does not splash all over the place. Pull the pull start several times. The fuel wil...

How To: Rebuild the clutch of an RC Nitro engine

Watch this instructional video as Alishan Mao takes you through a step by step tutorial on how to rebuild a 2-Stroke Wi X 18 Nitro Engine Clutch. The host provides you with a full list of tools needed to complete the job, as well as a list of common replacement parts. From here he shows you how to break the piece down, replace old and worn out components, then restore it to it's normal working order. Helpful tips include how to avoid damaging internal parts during repair, reattaching those tr...

How To: Replace a broken axel on your Volcano SV 4WD truck

In this how-to video, you will learn how to replace a broken axle on a Volcano SV. First, take off the wheel. Next, remove the axle piece out with a hex wrench. To get it entirely out, use your hex wrench to move out the long screws. Make sure you take them out at about the same time, or you will break one of the screws. You can remove the screw to free the upper suspension arm. This will make it easier to remove the broken axle. Next, replace it with a new axle. Clean the axle before making ...

How To: Make swords & hearts out of balloons

This video demonstrates how to make a balloon sword and heart. To make a sword, pump up a balloon as long as possible and tie the end. Twist the balloon at this end making a small ball. Bend the balloon at around 20 cms in length and twist both the ends of the balloon at the same level as the ball creating a loop. This is named the 'elephant bend'. Now insert the long end of the balloon into the loop leaving behind a small part. Your sword is ready.To make a Heart flower. Take a red balloon a...

How To: Make a 'redneck' wind chime from old gas tanks

This video is about how to make a wind chime from empty oxygen cylinders. It may be also known as a "redneck" wind chime. As a safety precaution use a small nail to go inside and make sure all the air is out. Use a small hand hack saw and cut slowly to make sure all the air is out. To suspend the cylinders from the middle use wire wrap. Make one loop to begin with and go around to the opposite side and mark the place. Make a single loop cross the wires over, use a pair of pliers where they cr...

How To: Install a 2-speed differential gear box in a RC buggy

In this how-to video, you will learn how to put back a 2 speed central gearbox in your RC vehicle. Take the time to clean your car. Remember that the shorter dog bone goes to the rear and the longer one goes to the front. Slide the dog bone in and make sure that it spins the wheels. Now, raise the dog bones and slide them into the drive cuffs of the central transmission. Once this is done, check by moving the tires to see if the gears are moving. Make sure the box fits into the place provided...

How To: Clean a penny with hot sauce

In this video, 305 Nicky shows the viewers how to clean up a penny by using Tabasco sauce. You will need a piece of sturdy paper towel, Tabasco sauce, and an old penny. Next, fold the paper towel into fourths and put the penny on top of the paper towel. Open the Tabasco sauce and put 4 or 5 drops onto the dirty penny. Make sure the penny is evenly coated by spreading it with your index finger. Wait for about 10 to 20 minutes after applying the sauce and using the paper towel, beginning to rub...

How To: Tune the ACME Attacker 1/8 scale RC Nitro engine

This video shows you how to tune the ACME attacker 1/8th scale nitro engine buggy. Use the high end valve and the idle speed screw as show in the film. Turn the engine and get it to the operating temperature and drive round to the see how the car performs. If the acceleration is sluggish then the low end valve should be adjusted. If the engine is having too much RPM then the idle speed should be reduced using the idle speed screw. If the engine bogs down and makes noise on full throttle and i...

How To: Make deadly homemade bolts

In this Hobbies & Toys video tutorial you are going to learn how to make deadly homemade bolts. Take a pencil and remove the ferrule from the end of the pencil. Make sure to pull it off completely so that you expose the flat end. Then take three pieces of electrical tape and tape them on the pencil and on to each other so that they form three wings. Now take a tack pin and with the help of nose pliers and pliers break off the rear end. Apply some hot glue to the ferrule end of the pencil and ...

How To: Make a basic rubber band car

To make a rubber band car you will need one sheet of card stock, four paper clips, two binder clips, one plastic straw, 8 inches of dowel that fits into the straw, two pencils and one rubber band. You will also need four CDs or round pies of cardboard, tape, a ruler and a marking pen. First, unfold the paper clips. Then fold the card stock and attach the paper clips. Cut squares out of the card stock. Then, cut the straw. Attach it to the card stock. Affix the pencils to the card stock with h...

How To: Make wind chimes using salt and pepper shakers

Here is a very crafty and cute way to create a wind chime out of old salt and pepper shakers that can be found either around your house or bought at second hand stores and a small tin tray or plate to hang your shakers from. A bit of out door or water-proof glue and some colorful string or twine, scissors and a nail or awl will finish out all the supplies you need.

How To: Repair the remote start system in the ACME RC car

This video is a Hobby Estore Video Tutorial that will show you how to repair or replace the ACME remote start system in your radio control cars. You will know you need to take this step when your RC car doesn't start or when you push the start button and all you hear is a clicking noise. The first step is to remove the remote start system and this can be accomplished by taking the top cover off of the car and then unhooking the exhaust hose from the remote start system. Then take the cover of...

How To: Make a great RC jump ramp from a box

The video demonstrates how to make a great RC jump ramp free of cost. Firstly for this you have to note that you must learn to control your RC in the air because wrong landings after high jumps can cause severe damage to your RC.To make a great ramp for jumping first take a box, a small box is taken here. The same can be done on a bigger box. Then opening the box cut the lateral upsides of the box. After that just put it down and put a tape at the place it touches the box. A curve as you desi...

How To: Land a Nitro RC plane

First of all you have to loose the altitude by taking a circle or two around in the air. On the final turn make a good straight approach to runaway and don't use too much ‘ailerons’ then. Just use the controls ‘rudder’, ‘elevator’ and ‘throttle’. Also watch for the cars or the traffic where you are going to land. Keep constant low ‘throttle’. You have to maintain good ‘idles speed’. You might want to adjust and remember the trim settings. After touch down, don’t pull on elevator. Just cut the...

How To: Make snow bases for your miniatures

The materials you will need to add snow and other details to the base of your miniature game figure are white tacky or craft glue, super glue, a few small rocks or pebbles, coarse turf, a small paint brush, and baking soda. Begin by using the super glue to apply a few rocks to your base. You don't want to apply too many as the main focus will be on the snow. Add white glue to the base being careful not to get any on the figure itself. Use your paint brush to spread the white glue around until...

How To: Yo-Yo like a pro

Yo-yo's are not just for kids anymore. Check out this funky tutorial and learn how to yo-yo like a pro. You can do way more than just pull your yo-yo up and down, with a little practice you will soon be performing tricks and spinning your yo-yo all over the place!

How To: Modify a Nerf Longshot CS-6 gun

Nerf guns are a great way to battle without inflicting serious injury. This video tutorial shows you how to modify a Nerf Longshot CS-6 by adding an angel breech and altering the clip to accept stefan bullets. This instructional also shows how to add gun spring reinforcements to insure the weapon operates well under the increased force. Finally, you'll learn how to integrate the front gun and link the trigger to the main Longshot spring mechanism for added fire power.

How To: Make a mini strawberry for a dollhouse

Garden of Imagination shows you how to Make a Strawberry for a miniature dollhouse from polymer clay. take a pinch of dark red clay, roll it into a ball, then a cone-shape around one centimeter or just under half and inch long. Poke a toothpick into the center of the fat end of the cone. Use another toothpick or a small ball-ended poker tool to put many small depressions around the tapering sides of the cone to represent pips. For the leafy strawberry top, use a small star-shaped cutter to cu...

How To: Make a Barbie-sized princess tiara

For the fairy sized princess tiara you will need 32 gauge silver wire, silver ball beads, seed beads (your choice of color) and 4 mm crystal beads. Start with about 6" of the wire. String a seed bead to the center of the wire- and twist one or two times to secure it in place. Then bring both ends of the wire together- and clip so that they are even. Next string a 4 mm crystal bead over both pieces of wire and press snugly next to the first seed bead already strung. Then add a silver ball bead...

How To: Make a mini cupcake for a dollhouse

Garden of Imagination demonstrates how to make a miniature polymer clay cup cake. First, roll a ball of brown clay into a circle. Squish it a little on its side. Use a toothpick to create edges on the cupcake. Make the top more pointed. Flip the cupcake over so that it sits flat. Bake the base for a few minutes to make it hard so you don't lose your texture. Roll your clay icing color into a long, thin rope. Wrap the icing in a conical circle on top of the cupcake base. Next, use tiny glass s...

How To: Make a homemade rocket in less than five minutes

In this video we are shown how to make a homemade rocket. The necessary items are as follows: A plastic bottle, a bicycle pump and a cork. First, cut the cork in half and make sure that it fits in the mouth of the bottle. Next, take a nail and push it through the cork so that it makes a hole going from one flat side to the other. Remove the nail and replace it with the needle from the bicycle pump, making sure that the needle is fully through the cork so that it is sticking out the other end....